Product # 6320, 6320C, 6321, 6321C, 6325, 6325C, 6326, 6326CIntegrated Sensor Suite Installation Manualfor Vantage Pro Weather Stations
Preparing the ISS for Installation: Prepare the Rain Collector86. If the LED flashes repeatedly but your console isn’t picking up a signal anywhere in
Siting the ISS and Anemometer: General ISS Siting Guidelines:9Siting the ISS and AnemometerFor your weather station to perform at its best, use these
Siting the ISS and Anemometer: General ISS Siting Guidelines:10• Range may be reduced by walls, ceilings, trees, foliage, a metal roof or other large
Installing the ISS: General ISS Installation Guidelines11Installing the ISSThe anemometer and the main part of the ISS can be installed either togethe
Installing the ISS: Installing the ISS on a Flat Surface12Installing the ISS on a Flat SurfaceRefer to the following illustration to install the ISS o
Installing the ISS: Installing the ISS on a Pole13Installing the ISS on a PoleWhen installing the ISS on a pole, the rain collector and radiation shie
Installing the ISS: Installing the ISS on a Pole14Installing ISS and Anemometer TogetherPlease remember to install your ISS so the anemometer arm is a
Additional Mounting Options: Finishing the Installation153. Swivel the anemometer until the arm is pointing north.If the anemometer arm is not pointin
Maintenance: Relocating the Anemometer16Relocating the AnemometerUsing Extension Cables: Note: Not all cables are compatible with your Vantage Pro sys
Troubleshooting: Cleaning the Radiation Shield17Cleaning the Radiation ShieldCheck the radiation shield for debris or insect nests at least once a yea
© Davis Instruments Corp. 2001-2004. All rights reserved.Integrated Sensor Suite Installation ManualRev. B, January 26, 2004Document: 07395.149Product
Troubleshooting: The Most Common Anemometer Problems18The Most Common Anemometer ProblemsNote: If the anemometer is sending no data, the wind display
Appendix A: Wireless Transmitter IDs: Changing ISS Transmitter ID19Appendix A: Wireless Transmitter IDs Changing ISS Transmitter IDEach wireless trans
Appendix B: Optional Accessories: Using Multiple Transmitting Stations20Using Multiple Transmitting StationsThis table shows the maximum number of eac
Appendix C: Re-orienting the Wind Vane: Other Accessories21Appendix C: Re-orienting the Wind VaneYour Vantage Pro station is configured to register wi
SpecificationsComplete specifications for the ISS and other products are available in the Weather Sup-port section of our website: www.davisnet.com.Ca
Introduction: Included Components and Hardware1IntroductionThe Integrated Sensor Suite (ISS) collects outside weather data and sends the data to a Van
Preparing the ISS for Installation: Tools for Setup2HardwareTools for Setup• Small Phillips-head screwdriver • Scissors or wire-cutters• Adjustable wr
Preparing the ISS for Installation: Assemble the Anemometer3Attaching Anemometer Arm to Base1. Insert the anemometer arm into the base, sliding the ca
Preparing the ISS for Installation: Check SIM Sensor Connections43. Push the wind cups up onto the anemometer’s stainless steel shaft.4. Slide the win
Preparing the ISS for Installation: Cabled ISS: Powering and Testing5Connect the Anemometer Cable to the SIM1. Unwind the coil of cable enough to work
Preparing the ISS for Installation: Wireless ISS: Powering and Testing6Troubleshooting Cabled ISS CommunicationIf your console is not receiving sensor
Preparing the ISS for Installation: Wireless ISS: Powering and Testing74. If you see the ISS ID number, press and hold down the DONE key to view ISS d
Comments to this Manuals